Hotrodders Bulletin Board - 19,20,21,22,23,24,32,34,36Get all of your tech questions answered on the net's largest community for hot rod and muscle car enthusiasts!Cooling System and Tranny Ford F-100- June 30, 2008 I have a 71 Ford F-100 that has pretty much just sat in my garage for the past 5 months and only moved once. Looking underneath it, the transmission is leaking fluid into a pretty decent size puddle and some folks I talk to say its normal if you dont move the vehicle but I wanted a second...http://www.hotrodders.com/forum/cooling-system-tranny-ford-f-100-a-141168-newpost.html?s=3... Newbie question Motorcraft 2100 Choke- June 29, 2008 Hi, great forum, I have a pretty novice question on a Motorcraft 2100 2bbl carb. I know from searching.. many think these carbs blow.. :( but I like the simple aspect of it and reliability for a Land Cruiser v8 conversion I have. My question is two fold, I went with a manual choke on the MC...http://www.hotrodders.com/forum/newbie-question-motorcraft-2100-choke-141167-newpost.html?... Engine and Transmission Leveling- June 29, 2008 Hi, I am new this. I am building a 1929 Ford Hi-Boy with a Chevy 350 engine and 350 transmission. I have built the rolling chassis. I am now about to install the engine and transmission. My question is on leveling. Do I make sure the Enginetransmission is level at the top of the carb, valve...http://www.hotrodders.com/forum/engine-transmission-leveling-141166-newpost.html?s=318e0d5... 235 Engine- June 29, 2008 I'm rebuilding a 57 chevy 3100 pickup truck with the 235 engine. I was told recently that the engine is in bad condition. I wanted to restore this vehicle with the original engine. I need to know if its worth it to have this engine machined due to its condition or look for a engine that does not...http://www.hotrodders.com/forum/235-engine-141165-newpost.html?s=318e0d5da26adcd13148523e4... 1993 Taurus toe-in Spec...- June 29, 2008 Can anyone tell me the front end toe-in specification for a 1993 Taurus GL. It is coming up .5 degree, toe-in per side as best as I can measure for a total of 1 degree toed-in. It also appears that there is no way to adjust front end caster or camber on this car. Does that sound righthttp://www.hotrodders.com/forum/1993-taurus-toe-spec-141164-newpost.html?s=318e0d5da26adcd... 468 w blower- June 29, 2008 i just got 81 chevy c10 lwb for a 100bucks. i got it home n found a 454 n it. i want 2 make it 468 with a blower. I want 2 use a 270comp cam, sum aluminun oval port heads,accu drive timing set,magnum push rods,aluminun rockers,850 blower carb,headers from hooker,3inch exhuast w X-pipe,hush power...http://www.hotrodders.com/forum/468-w-blower-141163-newpost.html?s=318e0d5da26adcd13148523... Is it worth changing press in rocker studs to screw in myself- June 29, 2008 I popped the driver side valve cover yesterday and noticed a broken rocker stud. I have seen tools for $20-$30 that allow you to pull the press in studs using the adjacent rocker stud. It also allows you to align the tap for screw in studs. Is this something I would just be better off allowing a...http://www.hotrodders.com/forum/worth-changing-press-rocker-studs-screw-myself-141161-newp... Single Stage Urethane Restoration Shop- June 29, 2008 Has anyone ever used Single Stage Urethane Restoration shop paint. I was going to go with kirker but couldn't find a blue I liked. http:www.tcpglobal.comrestorationshophttp://www.hotrodders.com/forum/single-stage-urethane-restoration-shop-141159-newpost.html... alcohol carbs- June 29, 2008 On you guys and gals that run carbed alcohol, what carbs do you guys run as looking to switch to alcohol as can not keep current motor cool. It is a 350 010 splayed-cap block bored .060 with a 3.5 stroke with appr 14.5 compression that currently has a 850 on a Super Victor & HVH 2" spacer on Dart...http://www.hotrodders.com/forum/alcohol-carbs-141158-newpost.html?s=318e0d5da26adcd1314852... CAM swap - Let me know what you would run!- June 29, 2008 So, currrently Im running a COMP Magnum 280H Here are my specs otherwise: Chevy 350 4 bolt Stock Crank 0.40" over Keith Black pistons 9.77:1 Stage 1 Rods World Products Sportsman II Heads 2.021.60 Manley Swirl Valveshttp://www.hotrodders.com/forum/cam-swap-let-me-know-what-you-would-run-141155-newpost.htm... |